info@pinnaclecad.com     |     

MEP Design Services

A well-designed and implemented MEP System should go virtually unnoticed. Designing systems that balance comfort, cost, efficiency and aesthetics require a synchronized team effort. We see ourselves as the facilitator of this team, assisting with decision making, cost estimation, construction administration, documentation, building management and maintenance.

Our MEP design services ensure higher ROI, fewer reworks, and improved schedule performance.

Our 200+ experienced professionals have worked on 570+ projects across sectors such as hospitality, educational, healthcare, residential, commercial, and industrial. 

MEP Design Services

Our assurances: energy-efficient designs, optimized operating cost of mechanical systems, and minimal risk of system failure. We offer:
  • HVAC System Design
  • HVAC Equipment Selection
  • Equipment & Duct Sizing Calculations 
  • Air Terminal Selection 
  • Lift Well & Stairwell Pressurization System
  • Tunnel & Basement Ventilation 
  • Chilled Beams System
  • Plant Room Layout Design
  • HVAC Schematic Design
  • Chilled Water Schematic
  • Duct Layout Drawings
  • Spool Drawings
We develop electrical design documents for low voltage, medium voltage, and extra low voltage systems, and ensure an energy-efficient design through BIM integrated Electrical Design Engineering. We offer:
  • Power Distribution System Design
  • Electrical Panel Schedules
  • Electrical Line Diagrams & Load List Preparation
  • Power And Lighting Plans (Including Lighting Load Estimations and Light Fixture Layouts)
  • Emergency System Design
  • Containment Sizing & Layout Design
  • Determining the Sizes of Switchgear & Transformers
  • Determining the Sizes of Breaker & Disconnects
  • Load Balancing
  • Panel Room Layout Drawings
  • Small Power Electrical Supplies
  • Fire Alarms & Security Systems
  • IT & Communication Systems
  • Lift And Escalator Systems
  • Lightning Protection & Earthing
  • Energy Management
Pinnacle uses BIM integrated plumbing design to cover:
  • Potable / Domestic Water Systems
  • Hot Water Systems
  • Wastewater Systems
  • Rainwater / Stormwater Systems
  • Medical / Fuel / Natural Gas Systems
  • Compressed Air Systems
Our in-house software tools help clients design their plumbing systems, including pipe sizing, roof area, and GPM flow rate optimization. We also offer:  
  • Water Demand Calculation
  • Sizing & Selection of Water Heater, Pumps & Water Storage Tanks
  • Pipe Sizing for Water Services
  • Water Services Schematics
  • Design of Gravity Based Soil & Waste System
  • Soil & Waste Schematics
  • Medical Gas & Vacuum Piping Design
  • Fuel Gas Piping Design
  • Plant Room Layout (Plans & Details)
  • Equipment Datasheets for Plumbing Equipment
  • Selection of Insulation for Piping Materials
  • Preparation of Design Requirement Document / Specification
  • Discharge Unit & Storm Water Calculations
  • Design & Preparation of Schematic Diagram
  • Design & Preparation of Plan & Layout Drawings
  • Accurate and information-rich fully coordinated 3D models generated post inter-trade clash resolution that facilitate spatial coordination.
  • A process that determines the accuracy & reliability of construction documents for seamless construction by reducing delays, reworks and cost overruns.
  • Review and reimagination of the layout to produce the most efficient design and achieve the minimum project cost at maximum operational efficiency.
  • Precise material quantities of all equipment, fixtures, and conduits details in a tabulated format generated from coordinated 3D BIM models to help contractors in estimating project costs and plan material procurement.
  • Quantity Take Off is dynamically generated from the BIM Model. This list is automatically updated if any changes are made to the existing 3D Model.
  • Accurate sleeves, penetration and hanger location drawings to facilitate fabrication or on-site construction.
  • Our Shop Drawings are dynamically generated from the 3D Model as per the client’s prescribed standards and requirements. Any changes to the model will automatically be reflected within the shop drawings.
  • Accurate spool drawings to facilitate spool assembly for piping runs and pre-fabrication.
  • Alignment of segmented spools drawings with the contractor’s prefabrication standards and preferences.
  • Provision of module drawings for modular prefabrication to lower cost, shorten installation time and improve site safety.
  • Data-rich 3D models including information like warranties, equipment lists and product data for facility management.
  • The COBie format allows the gathering of data throughout the design phase which is subsequently transferred to the owner.
  • COBie data is integrated into the BIM model to facilitate maintenance, operations, and asset management.
  • Data-rich 3D models including information like warranties, equipment lists and product data for facility management.
  • The COBie format allows the gathering of data throughout the design phase which is subsequently transferred to the owner.
  • COBie data is integrated into the BIM model to facilitate maintenance, operations, and asset management.
  •  

The Pinnacle Advantage

What Our Clients Say

Printable Brochure

BIM Services for MEP Engineers

Engineering Brochure

We'd love to hear about your next project.

©2021 pinnaclecad.com | Privacy Policy